Videofied XTO-IP210 GPRS/IP with I/O and GSM/RF booster Waterproof-IP65/Wireless/Cordless Alarm Syst

Videofied XTO-IP210 GPRS/IP with I/O and GSM/RF booster Waterproof-IP65/Wireless/Cordless Alarm Syst


shop price: € 995.00
web price: € 895.00

AddThis Social Bookmark Button
Videofied XTO-IP210 GPRS/IP with I/O and GSM/RF booster Waterproof-IP65/Wireless/Cordless Alarm System

The XTO-iP GPRS alarm panel is a Videofied weatherproof, wireless, battery operated security system. The control panel is designed for outdoor commercial applications (constructions sites, cellular towers, remote sites, substations...). The box is water-resistant and temperature-resistant. The control panel is powered by 4 LSH20 Lithium batteries that last up to four years, with normal system activity. A dual-tamper function is active 24 hours, whether or not the system is armed. An alarm occurs if the control panel cover is removed, or if the control panel is removed from the mounting surface. The user can arm and disarm the system by entering his code on the external keypad. A radio antenna is built in the system.

Supervised Wireless Technology
The XTO-iP series, along with all Videofied devices uses patented S2View - Spread Spectrum, Videofied, Interactive, AES Encrypted Wireless technology, providing optimum signal integrity and security. Bi-directional RF communication between all system devices and the system control panel ensures high signal reliability. The panel supervises every device (excluding the remote keyfob) to monitor current open/close state, tamper condition, serial number, date of manufacture, firmware revision, and battery status.

- S2View: Spread Spectrum, Videofied, Interactive AES Encrypted Wireless technology provides optimum signal integrity and security.
- Compatibility: works with all Videofied wireless devices.
- Supervision of all devices (except remote keyfob).
- Tamper detection: 24-hour dual-tamper function provides detection for both cover and wall removal. Control panel also monitors all system device tamper switches.
- Zones/Devices: 25 maximum.
- Areas: 4 maximum. Area 1 predefined from factory for entry/exit delay. Areas 2, 3, and 4 can be configured as needed.
- Access codes: 20 maximum, 4 - 6 digits; one installer access code for on-site programming only.
- Configuration/Programming: on-site using alphanumeric keypads.
- Communication: reports to central monitoring stations using Frontel.
- Video verification: video resolution of 320 x 240 pixels, 0 lux sensitivity, 5-frames per second for approx. 10 seconds total recording time. 220K MPEG file.
- History/Event Log: maximum 4,000 events stored in flash memory that cannot be cleared or erased.

Complete system configuration/programming can be done on-site using alphanumeric keypads. Easy to understand text on a two line, 16-characters liquid-crystal (LCD) display guides you through programming, prompting you for simple yes/no or data entry responses. Complete punctuation symbols allow for accurate website/IP address entries and device location naming.

The XTO-iP reports alarms and other system events by using the Frontel protocol. Frontel provides complete system reporting information and video verification to a central monitoring station set up with the Frontel alarm receiving software.

Video Verification
Incorporating MotionViewer into the security system allows for video verification of intrusion alarms. When the system is armed and an intruder trips MotionViewer, the integrated camera captures a 10-second digital video clip which is sent to the central monitoring station by the control panel, which can forward them to an alert list.

History/Event Log
The XTO-iP control panel records and stores all system activities and events (armings, disarmings, alarms, access codes entered, system programming changes, etc.) in flash memory, that cannot be cleared or erased. The log accumulates a maximum of 4,000 events. As additional events occur, the control panel automatically deletes the oldest event. This ensures the most recent events reside in the log. The history/event log can be viewed using an alphanumeric keypad or downloaded at the monitoring station.

Power supply (NOT INCLUDED)
Power supply Type C 14.4V with 4x3.6V Lithium batteries /LSH20 (NOT INCLUDED)
Low battery limit 12 V
Battery life (average) 4 years

RF S2View technology
Radio type Bidirectional RF
Operating frequency
868MHz - XTO-iP 210 (Europe, South Africa, Asia)
915MHz - FHSS - XTO-iP 630 (USA, Canada, South America)
920MHz - FHSS - XTO-iP 730 (Australia, South America)
Transmission security AES encryption algorithm
Radio jam detection Yes
Supervision Yes
Radio Antenna integrated
External RF antenna Yes via MMCX connector

Autoprotection Cover tamper

Communicator type 2G3G
Security protocol Frontel
IP stack TCP/IP
Video transmission By Frontel protocol to central monitoring station or App servers
2G3G Antenna Integrated
External 2G3G antenna Yes via MMCX connector

Video Format WMV or MPEG
Images per second 5
Image size 320x240 or 640x480 pixels
Video length 4 to 12 seconds

Programming Keypad
Max number of devices 24
Max number of codes/badges 19
Arming modes 4
Areas 4
Event log
4000 events stored on flash memory
Events memory storage delay

Physical and Environmental Data
Operating temperature -25 C/70 C
Maximum relative humidity 95%, sans condensation
International Protection Marking IP65 / IK06
Material ABS-ULV0

Installation / Mounting
Control panel / Base
4 screws to close the cover
4 screws on panel base for brackets mounting

Panel 272 mm x 276 mm x 96mm

XTO-iP210 Compliant with the annex IV from the R&TTE 1999/5/CE Directive
XTO-iP630 USA FCC (Part 15C, 22H, 24E & 27) Canada IC (RSS-210 Issue 8, RSS-132, RSS-133 & RSS-139)
XTO-iP730 Australia A-Tick (AS/NZS4268, AS/CHS42 & AS/NZS 60950)



SoundTech Ltd SoundTech Ltd SoundTech Ltd SoundTech Ltd